Fermentation

Solid Rubber Stopper bungs. Various sizes available. Use a solid or drilled rubber stopper with your carboy, fermenter, growler and more.

This airlock is a replacement piece for our stainless steel variable capacity wine tanks. Used for releasing pressure when the lid is down on top of the wine, and the bladder is fully expanded. Size opening 1-7/8".

These carboy's are made of PET, are odorless and virtually impermeable to oxygen. A BPA-free plastic, which allows beverages to sit for several months in the carboy without the worry about oxidation. This combines the barrier properties and visibility of glass, with the convenience and safety of unbreakable plastic. Easier to clean thoroughly than ribbed carboys.

Ideal for secondary fermentations.
Also perfect for bulk aging.
Completely taste and odor-free.
It is stain resistant.
There are no ribs on the sides to collect yeast or sediment.
Therefore it is very easy to clean, inside and out.
Impermeable to oxygen.
Safe to reuse over and over, if properly sanitized before and after each use.
Takes our # 10 Rubber Stopper or Medium Boun Vino Stopper.
Weighs approximately 1.5 lbs
Rated to 140 degrees F

The bung is made from 100% FDA approved, food grade pure silicone rubber, a durable material resistant to sulfur dioxide.

Fits a standard wine barrel.

Size: 50 mm bung hole

Fill with distilled water or alcohol and insert in drilled stopper or bung to vent gases during fermentation. Includes body, piston, and vented cap. Easy to disassemble and clean out.

55 gallon blue industrial drum includes a sealed tight-head with 2 bungs and is BPA free.

DESCRIPTION

Chilling plates are a great addition to our variable capacity tanks, macro bins, or any vessel used to control fermentation temperature. These heat exchangers work with glycol chillers as well as pump cycled cold water. Made of AISI 304 bright annealed stainless steel with a polished finish. Inlet and outlet are 1/2" male pipe thread (MPT). 

Sizes Available:
300 Liter (31.5" x 14.5")
500 Liter (39.5 x 14.5")
600 Liter (47.5" x 14.5")
800 Liter (59" x 14.5")

DESCRIPTION

These stands fit our Flat Bottom Variable Capacity Tanks. They raise the tanks approximately 16 inches off the ground allowing better access to the Tri Clamp fitting. 

Wine Whip Degasser

This wine whip is a great degassing tool that helps to kick carbon dioxide out of solution, making your wine still and delicious! The wine whip is safe for use with glass. For best results, use with a standard 3/8" variable speed drill. Angle slightly while operating and make sure to keep your speed even. This wine whip can be used on standard carboys of 3, 5, 6, and 6.5 gallon sizes. An effective and economical solution to degassing your wine!

Stainless steel baster for drawing samples from your vessel.

Specially designed for mixing and stirring wine/beer and de-gassing.
Manufactured in high quality food grade stainless steel with ABS blades.
The blades act like a turbine for maximum mixing and stirring efficiency.
The Stainless Steel Mix-Stir fits any electric drill (variable speed drill with reversing capacity recommended).

Length: 22"

The Plastic blades fold down allowing easy insertion into a barrel or a glass carboy. Also, it is safe to use with glass carboys.

Heavy Duty Glass Wine Thief. 18" long, 1.25 inches thick, with glass "D" handle and bent to work with stacked barrels. Very sturdy and perfect for sampling for testing as well as for special events.

Stainless steel stand for barrel cleaning with a rotating jet spray barrel cleaning head, efficiently clean barrels. Stainless steel 3/4" ball valve for water shut-off is included. Hot water use with water pressure of 60 to 70 psi is suggested.

A liquid crystal thermometer that adheres to the side of a carboy, bucket, or even stainless conical to tell you the fermentation temperature in degrees Fahrenheit. Scale of 44–86°F.

This air pump has a pressure gauge, and an indicator mark to insure proper sealing. With a hook for convenient hanging on side of tank. Making sure your lid bladder is properly inflated is key to sealing the top of your variable capacity wine tank, this air pump is easy to use and easy to read.

Replacement pump assembly for any variable volume fermenter. Includes built-in gauge and line to connect with gasket, but does not include gasket. Made in Italy. 

Pneumatic air pump for variable capacity (VC) tanks. Features a 3/8 in barbed nipple to attach a length of tubing. Can be used with VC tanks from most manufacturers.

Speidel is a German manufacturer of premium quality stainless steel tanks for the wine industry. The tank body is fabricated from 304-type stainless steel, while the floating lid is made from 316-type stainless and has an inflatable bladder that pumps up to seal the wine off at any volume level. They can be used for primary fermentation as well as aging. These tanks arrive to you complete and ready to go out of the box after a little assembly. The tanks are fitted with 1/2" threaded ports to accomodate the included 1/2" stainless steel ball valve and 1/2" stainless plug. The plugged port is intended for use with an optional thermometer. Comes with a rubber lid gasket, high-quality laser welds, ultra smooth interior surface for easy cleaning, and a 25 year warranty from Speidel covering defects and craftsmanship.

These heavy duty Speidel tanks from one of the most trusted names in fermentation are equipped with a number of different features that simpler carboys just don’t have. Their oversized top openings make cleaning a breeze, while the integrated handles make for easy transportation, even when full.

All Speidel fermenters are made of high density polyethylene (HDPE) plastic that is much thicker than traditional plastic used on most carboys. They also come in sizes that can accommodate up to 30 gallons of liquid. Speidel’s high-density construction is resistant to oxygen ingress, which makes them suitable for aging beverages for up to 12 months.

These one-piece polypropylene shovels are tough, lightweight and hygienic. Molded from FDA-compliant polypropylene, it is a workhorse for moving bulk materials and an integral part of any professional cross–contamination containment, food safety or HACCP program.
Large measures 14" x 43"
Medium measures 11" x 38"

These stainless punch-down tools are ideal for punching the cap on a red wine fermentation back into solution. A 48" long punch is great for the winemaker fermenting in plastic barrels, small stainless fermenters, Brute fermenters, or macro bins. 48" long with an 8" disc.

Propylene Glycol is used with water to create the cooling medium in Glycol Chillers. Adding glycol to the water lowers the water's freezing point, allowing the cooling medium to drop below freezing. This makes the cooling system more responsive to temperature changes in your storage vessels, and makes it possible to bring the wine down to cold stabilization temperatures as well as controlled fermentations.

Constructed from heavy duty, type 304 stainless steel with an electropolished finish to enhance corrosion resistance, improve surface finish and for ease of cleaning. Ideal for use in food the processing industry. Fully welded and completely seamless to ensure that there are no spaces where any particles can gather. 48" in length. Paddle Head Size: 4-3/4" x 9".

Clear glass marbles are a great choice for filling up volume in a small fermenter or oak barrel.

Clear glass marbles, free of ink or contamination, are an ideal solution. Use just as much as you need to top up the vessel. When you transfer the beverage out, remove your marbles, wash and reuse with your next batch.

3 lbs of marbles is enough to displace approximately 1 Liter of liquid or 1/4 gallon.

The FastFerment System is a one-stage fermenter, which allows brewers & winemakers to do primary & secondary fermentation in the same unit. FastFerment eliminates racking & transferring between buckets & carboys. This saves approximately 80% of the time & labor needed to make a batch of beer or wine compared to traditional methods. With less equipment, clean up is easy.

Why Use FastFerment?
Guaranteed Consistent Batches
Primary & Secondary Fermentation in the Same Container
No Transfers & No Racking - 80% Less Work
Better Quality Product with No Sediment Contamination
Increased Sanitation with Less Contamination
Less Oxygen Exposure
Ability to Harvest Yeast & Save for Reuse

Features and Benefits
Easy Cleaning and Batch Stirring - 6" (15cm) removable screw top
Total Capacity 7.9 US Gallons/ 30 Litres - Made for 5 - 7 Gallon batches with blow offs
Easy Wall Mounting System - Mounts to standard 16" (40cm) wall studs
1" (2.5cm) Bottom valve compared vs. 3/4" (2cm)
Collection Ball for Yeast Harvesting - Save $100's & harvest your Yeast Strains!
Temp. Monitoring - ThermoWell included - Thermometer Avail.

Kit Contents
One 7.9 US Gallon / 30 Litre Conical Fermenter
6" (15cm) Screw Top, Grommet & Airlock
Bottom Collection Ball For Harvesting Yeast
1" Union Teflon Valve and fittings
Wall Mounts (2), Mounting Bolts & Anchors (4)
1/2" (1.25cm) PVC Hose (2' /60cm) & Hose Clamp
Permanent Thermowell for Temperature Monitoring
Instructions

Organize your fermentation space with these carboy stackers / dryers. Use the stand to dry the carboy after washing it.

Variable capacity tanks are stainless steel flat bottom fermentation tanks with a floating lid to allow for varying capacities of fermenting beverages. Stands are available and sold seperately. Tank's made with high quality AISI 304 stainless steel. They have a beautiful marbled finish on the outside, and a smooth polished finish inside.

Tanks include: Stainless steel floating lid, air pump, food-grade air tube, plastic tubing, tubing clamps, dry airlock, and one BSPP chrome plated brass ball valve.

300L Specifications:

• Nominal volume: 300 Liters (79.3 gallons)
• Effective volume: 305 Liters (80.6 gallons)
• Diameter: 65 cm (26 inches)
• Height: 100 cm (39 inches)
• Valve size: 3/4" BSPP 
• Thickness (Bottom X side, in mm): 1.0 X 0.7

*Note: Tank may differ slightly from image shown. Stands are sold separetely.

Red Rubber 50 mm Single Hole Carboy Cap. Fits 5, 6, and 6.5 gallon carboys.

Fits standard 3, 5, 6, or 6.5 gallon glass carboys. A racking cane can be placed through the center hole for transferring. The second hole can be used with tubing for a blow-off fermentation system.

Variable capacity tanks are stainless steel flat bottom fermentation tanks with a floating lid to allow for varying capacities of fermenting beverages. Stands are available and sold seperately. Tank's made with high quality AISI 304 stainless steel. They have a beautiful marbled finish on the outside, and a smooth polished finish inside.

Tanks include: Stainless steel floating lid, air pump, food-grade air tube, plastic tubing, tubing clamps, dry airlock, and one BSPP chrome plated brass ball valve.

400L Specifications:

• Nominal volume: 400 Liters (105.7 gallons)
• Effective volume: 405 Liters (107.0 gallons)
• Diameter: 65 cm (26 inches)
• Height: 130 cm (51 inches)
• Valve size: 3/4" BSPP 
• Thickness (Bottom X side, in mm): 1.0 X 0.7

*Note: Tank may differ slightly from image shown. Stands are sold separetely.

Stainless steel beverage bucket is easy to clean and is long lasting.

Food-grade plastic bucket for fermenting and storage of craft beverages. Drilled bucket makes an excellent bottling vessel used with a spigot.

Lid for fermentation buckets with grommeted hole for airlocks.